 
PROJECT DATA
------------
Project            : 
Designer           : 
Date               : May/24/2023
Checked By         : 
Date Checked       :  
User job number    : 
State              :                               State Job #: 
State Specification: None                         
Comments           : D40 Construction Load Check (LEAP Concrete Version 21:00:00:24):
                     (1)The bridge span is 40'-0", girder spacing is 7.5 feet, and deck overhang width is 3 feet 
                     and 1 inch.
                     (2)The structural depth of the deck and sacrificial wearing surface are assumed to 7.75 and 
                     0.75 inches, respectively. The thickness of the overhang tapers from 11 inches at the beam 
                     flange to 10 inches at edge of deck.
                     (3)The structural haunch thickness is 0.5 inches and the haunch thickness for calculating its 
                     dead load is 1.0 inches.
                     (4)One steel diaphragm of 0.285 kips is at the center of span.
                     (5)Dead load of forms: 0.010 ksf on the tributary area of the deck width with a 1.50 load 
                     factor. This load is applied to the full span length.
                     (6)Dead load of edge rail and walkway applied at the edge of the deck form: 0.075 klf [IDOT SS 
                     2403.03, L, 4, d.] with a 1.25 load factor. This load is applied to the full span length.
                     (7)Construction live load on walkway: 0.050 ksf [IDOT SS 2403.03, L, 4, e.] on a 2-foot wide 
                     walkway with a 1.50 load factor. This load is applied to the full span length.
                     (8)Construction live load on deck: 0.050 ksf [IDOT SS 2403.03, L, 4, e.] on the tributary area 
                     of the deck width with a 1.50 load factor. This load is applied from midspan to end of span.
                     (9)Live load of finishing machine located along the edge of the deck form to maximize the 
                     design condition: 9 kips with a 1.50 load factor. The load is placed as 4 individual point 
                     loads of 2.25 kips spacedon 2-foot centers with one of the middle point loads located at the 
                     center of the span.
                     NOTE:
                     The Final Stress limit for tension in the bottom flange for Service III, is set at zero, per 
                     BDM 5.4.1.4.1.3. 
                     It is permissible for the Service III tensile stress to exceed zero at the top flange near the 
                     beam ends, as long as it is within the 0.24?(f?c)0.5 tension limit at release.    
Design Mode        : AASHTO LRFD - 8th Edition
Units:             : US
Design as:         : Simple span
Flared Girder:     : No
File Name          : c:\users\9925\appdata\local\temp\1\leap_bak\lb_55cb.tmp\D40_Construction\BR01.csl
 
 
GEOMETRY DATA
--------------
 
BRIDGE LAYOUT                                 
-------------                                 
Overall width     , ft  =       36.333
Left curb         , ft  =        0.000
Right curb        , ft  =        0.000
curb-to-curb width, ft  =       36.333
Number of spans         =            1
Number of lanes         =            3
Lane width        , ft  =       12.000
Eff Deck thick    , in  =        0.000
Sacrificial thick , in  =        0.000
Haunch thickness  , in  =        0.000
Haunch width      , in  =        0.000
Bridge c/s,MI(Ixx), in4 =   1074870.00
 
SPAN DATA
---------
Precast length    , ft =     41.000
Bearing-to-bearing, ft =     40.000
Release span      , ft =     41.000
 
BEAM DATA
---------
 No               ID    Loc-prev    Area     MI(Ixx) Height   Yb   B-topg  B-Trib
                             ft      in2       in4     in     in     in      ft
 1             IA-Std-D    3.167    638.7   214974.0  54.00  24.37  20.00   6.917
 2             IA-Std-D    7.500    638.7   214974.0  54.00  24.37  20.00   7.500
 3             IA-Std-D    7.500    638.7   214974.0  54.00  24.37  20.00   7.500
 4             IA-Std-D    7.500    638.7   214974.0  54.00  24.37  20.00   7.500
 5             IA-Std-D    7.500    638.7   214974.0  54.00  24.37  20.00   6.916
 
 
MATERIAL DATA - Project Level
-----------------------------
 
As defined in Material Tab. For beam level properties look at Beam Specific output.
 
CONCRETE PROPERTIES
-------------------
                   Precast          C.I.P.
f'c ,ksi      =      5.000           4.000
Wc  ,pcf      =    150.000         150.000
Concrete Type =     Normal          Normal
Lambda        =      1.000           1.000
Ec  ,ksi      =   4286.830        4266.220
K1            =      1.000           1.000
f'ci,ksi      =      4.500 
Eci ,ksi      =   4066.840
K1            =      1.000
Thermal coeff.,1/F  = 0.00000600
 
STRAND AND REBAR PROPERTIES
----------------------------
PRESTRESSED STEEL:
0.6''-LL-270-72.6, Low relaxation strands 
     Straight Pattern
     Strand Diameter       =        0.600 in
     Tensile Strength(fpu) =      270.0 ksi
     Strand Area           =        0.217 in2
Use transformed strand and rebar: Strand Only
 
REINFORCING STEEL: Tension/Shear steel: fy = 60.0 ksi Es =  29000 ksi
 

 
LOADS DATA:
-----------
 
LOADS GENERATED USING PERMANENT LOAD WIZARD: NO
 
LOADS ON PRECAST
----------------
UNITS: (Point:  kips, Location: ft, Line:   klf, Trapez:   klf)
Span Beam DC/DW  Type       Mag.1   Loc.1   Mag.2   Loc.2     Description
   1    1    DC Line        0.068    0.00       0.068   40.00   Forms
   1    1    DC Line        0.075    0.00       0.075   40.00   Walkway DL
   1    1    DC Trapez      0.056    0.00       0.056   20.00   Additional Wet Deck Overhang
   1    1    DC Trapez      0.021    0.00       0.021   20.00   Haunch
   1    1    DC Trapez      0.726    0.00       0.726   20.00   Wet Deck
   1    1    DW Trapez      0.342   20.00       0.342   40.00   LL on Beam
   1    1    DW Line        0.117    0.00       0.117   40.00   LL on Walkway
   1    1    DW Point       2.350   18.00      -         -      Screed machine load 1
   1    1    DW Point       2.350   20.00      -         -      Screed machine load 2
   1    1    DW Point       2.350   24.00      -         -      Screed machine load 3
   1    1    DW Point       2.350   26.00      -         -      Screed machine load 4
 
DIAPHRAGM LOADS
---------------
UNITS: (Load:  kips, Location: ft)
Span Beam         Load Location
   1    1        0.143   20.000
   1    2        0.285   20.000
   1    3        0.285   20.000
   1    4        0.285   20.000
   1    5        0.143   20.000
 
LOADS ON COMPOSITE
------------------
UNITS: (Point:  kips, Location: ft, Line:   klf, Trapez:   klf)
       (Area:   ksf, Width: ft)
 
TEMPERATURE LOADS
-----------------
 
LIVE LOADS
----------
Live load deflection: not included.
ID: Design Lane - not incl. (Type: Design Lane)
ID: Design Tandem - not incl. (Type: Design Tandem)
ID: Design Truck - not incl. (Type: Design Truck)
 
Pedestrian Load - NONE
 

ANALYSIS DATA:
--------------
ANALYSIS PARAMETERS DATA
------------------------
 
  Truck impact:       1.330 
  Lane  impact:       1.000 
  Strength II impact: 1.330 
  Fatigue impact:     1.150 
 
 
DISTRIBUTION FACTORS (Art. 4.6.2.2):
------------------------------------
 
  Include sacrificial deck thick in ts:   NO   
  Is Span Post-tensioned:                 NO   
  ADTT (Average Daily Truck Traffic)    : 5000 
  Percent of the specified force effect : 1.00 
  Apply reduction of Moment for skew:     NO   
 
NOTE: Beam specific dead and live load DFs are printed in beam level reports.
 
LOAD FACTORS: (Table 3.4.1-1 & 3.4.1-2)
---------------------------------------
 
               Live DC(max) DC(min) DW(max) DW(min) 
----------------------------------------------------
  Service I:   1.00    1.00    1.00    1.00    1.00 
  Service III: 0.80    1.00    1.00    1.00    1.00 
  Strength I:  1.75    1.25    0.90    1.50    0.65 
 
 
----------
 
  Ductility Factor:  1.00 
  Redundancy Factor: 1.00 
  Importance Factor: 1.00 
 
----------------------------------------------------------------------------------------------------


PROJECT PARAMETERS DATA:
------------------------
MULTIPLIERS:
------------
 
  Trans len mult: Bonded   = 1.00 
                  Debonded = 1.00 
  Dev len mult:   Bonded   = 1.60 
                  Debonded = 2.00 
 
Camber & Deflection Multiplier (PCI ref.)
-----------------------------------------
 
                 Erection Final 
--------------------------------
  Prestress:         1.80  2.45 
  Self. Wt:          1.85  2.70 
  Deck + Haunch:           2.30 
  Diaphragm:               3.00 
  DL-Prec.:                3.00 
  DL-Comp.:                3.00 
 
MOMENT AND SHEAR PROVISIONS:
----------------------------
 
  Ultimate Moment Capacity, Mu-prvd computed:    AASHTO equations 
  Horizontal Shear, Beam and Slab effects in Vu: EXCLUDED         
 
STRESS LIMITS (Art. 5.9.2):
---------------------------
STRESS LIMITS AT RELEASE BEFORE LOSSES:
---------------------------------------
 
                     PRECAST     
---------------------------------
  Strength              4.50 ksi 
  Elasticity          4066.8 ksi 
  Max comp              2.92 ksi 
  Max tens             -0.19 ksi 
  Max tens,  w/reinf   -0.51 ksi 
 
STRESS LIMITS AT FINAL AFTER LOSSES:
------------------------------------
 
             PRECAST       DECK      
-------------------------------------
  Strength      5.00 ksi    4.00 ksi 
  Elasticity 4286.83 ksi 4266.22 ksi 
 
STRESS LIMITS AT FINAL 1 (P/S + DL + LL):
-----------------------------------------
 
           PRECAST     DECK     
--------------------------------
  Max comp    3.00 ksi 2.40 ksi 
 
STRESS LIMITS AT FINAL 2 (P/S + DL):
------------------------------------
 
           PRECAST     DECK     
--------------------------------
  Max comp    2.25 ksi 1.80 ksi 
 
FATIGUE I STRESS LIMITS AT FINAL 3 ( 50% P/S + 50% DL + F_LL ) (Art. 5.5.3.1):
------------------------------------------------------------------------------
 
           PRECAST     DECK     
--------------------------------
  Max comp    2.00 ksi   -  ksi 
 
SERVICE III (Tension):
----------------------
 
           PRECAST      DECK     
---------------------------------
  Max tens   -0.00 ksi -0.38 ksi 
 
RESISTANCE FACTORS (Art. 5.5.4.2):
----------------------------------
 
  Flexure Reinforced                   
  Compression controlled sections 0.75 
  Tension controlled sections     0.90 
                                       
  Flexure Prestressed                  
  Compression controlled sections 0.75 
  Tension controlled sections     1.00 
                                       
  Shear                           0.90 
 
PRESTRESS LOSSES:
-----------------
 
  Time Dependent Losses, Approximate Method (Art.5.9.3.3) 
  Days to release = 0.75                                  
  Rel. Humid.(RH) = 70.0 %                                
 
----------------------------------------------------------------------------------------------------


RATING PARAMETERS
-----------------
 
 
                  Rating Factors                     References     Values 
---------------------------------------------------------------------------
  Condition Factor                               Table 6A.4.2.3-1     1.00 
  System Factor for Flexural Effect              Table 6A.4.2.4-1     1.00 
  System Factor for Shear Effect                 Art. 6A.4.2.4        1.00 
  ADTT                                           Section C3.6.1.1.2   5000 
  Dynamic Load Factor for Design Level           Art. 6A.4.3.3        0.33 
  Dynamic Load Factor for Legal and Permit Level Table C6A.4.4.3-1    0.33 
 
For Flexural Effect: Condition Factor * System Factor = 1.00 >= 0.85 (Art. 6A.4.2.1) OK
For Shear Effect: Condition Factor * System Factor = 1.00 >= 0.85 (Art. 6A.4.2.1 and 6A.4.2.4) OK
 
Dead Load Factors (Table 6A.4.2.2-1)
------------------------------------
  Limit State  DC   DW  
------------------------
  Strength I  1.25 1.50 
  Strength II 1.25 1.50 
  Service I   1.00 1.00 
  Service III 1.00 1.00 
 
----------------------------------------------------------------------------------------------------


 
BEAM SPECIFIC MATERIAL PROPERTIES:
 
   Span#, Beam#      Tendon-ID     Girder-f'ci Girder-f'c Deck-f'c 
                                       ksi         ksi       ksi   
-------------------------------------------------------------------
  Span:1, Beam:1 0.6''-LL-270-72.6    4.50        5.00      4.00   
  Span:1, Beam:2 0.6''-LL-270-72.6    4.50        5.00      4.00   
  Span:1, Beam:3 0.6''-LL-270-72.6    4.50        5.00      4.00   
  Span:1, Beam:4 0.6''-LL-270-72.6    4.50        5.00      4.00   
  Span:1, Beam:5 0.6''-LL-270-72.6    4.50        5.00      4.00   
 
 
Span:1, Beam:1
 
PRESTRESSED STEEL:
 10 strands, 0.6''-LL-270-72.6, Low relaxation strands
Straight Pattern
 
END PATTERN (Ycg = 14.30 in):
 
  4 @  2.000 in 2 @  6.000 in 2 @ 10.000 in 2 @ 51.500 in 
 
REINFORCING STEEL:
 
  Tension steel:     
---------------------
  fy        60.0 ksi 
  Es       29000 ksi 
 
Stirrups:
 
  # legs    Size     fy   Area Spacing  Start    End    Extends  
                   (ksi) (in2)   (in)    (ft)    (ft)  into Deck 
-----------------------------------------------------------------
       2 US#4[M13]  60.0  0.40    9.00  0.1043  3.1043 Yes       
       2 US#5[M16]  60.0  0.62    0.00  0.1250  0.1250 No        
       2 US#5[M16]  60.0  0.62    9.00  0.5000  2.7500 No        
       2 US#5[M16]  60.0  0.62    9.75  2.7500  3.5630 No        
       2 US#4[M13]  60.0  0.40   10.50  3.1043  3.9793 Yes       
       2 US#5[M16]  60.0  0.62   11.25  3.5630  4.5098 No        
       2 US#5[M16]  60.0  0.62   12.00  4.5098  5.5098 No        
       2 US#4[M13]  60.0  0.40   12.00  3.9793  9.9793 Yes       
       2 US#4[M13]  60.0  0.40   18.00  9.9793 31.0207 Yes       
       2 US#4[M13]  60.0  0.40   12.00 31.0207 37.0207 Yes       
       2 US#5[M16]  60.0  0.62   12.00 35.4902 36.4902 No        
       2 US#5[M16]  60.0  0.62   11.25 36.4902 37.4370 No        
       2 US#4[M13]  60.0  0.40   10.50 37.0207 37.8957 Yes       
       2 US#5[M16]  60.0  0.62    9.75 37.4370 38.2500 No        
       2 US#5[M16]  60.0  0.62    9.00 38.2500 40.5000 No        
       2 US#5[M16]  60.0  0.62    0.00 40.8750 40.8750 No        
       2 US#4[M13]  60.0  0.40    9.00 37.8957 40.8957 Yes       
 
Top Steel:
 
  #bars    Size   Dist. from Top  Area  Start    End   Side Cover 
                       (in)      (in2)   (ft)    (ft)     (in)    
------------------------------------------------------------------
      1 US#4[M13]           2.00 0.200  0.0000  4.0000       3.00 
      1 US#4[M13]           2.00 0.200 37.0000 41.0000       3.00 
 
Bottom Steel:
 
  #bars Size Dist. from Top  Area Start  End Side Cover 
                  (in)      (in2)  (ft) (ft)    (in)    
--------------------------------------------------------
 
 
Span:1, Beam:2
 
PRESTRESSED STEEL:
 10 strands, 0.6''-LL-270-72.6, Low relaxation strands
Straight Pattern
 
END PATTERN (Ycg = 14.30 in):
 
  4 @  2.000 in 2 @  6.000 in 2 @ 10.000 in 2 @ 51.500 in 
 
REINFORCING STEEL:
 
  Tension steel:     
---------------------
  fy        60.0 ksi 
  Es       29000 ksi 
 
Stirrups:
 
  # legs    Size     fy   Area Spacing  Start    End    Extends  
                   (ksi) (in2)   (in)    (ft)    (ft)  into Deck 
-----------------------------------------------------------------
       2 US#4[M13]  60.0  0.40    9.00  0.1043  3.1043 Yes       
       2 US#5[M16]  60.0  0.62    9.00  0.5000  2.7500 No        
       2 US#5[M16]  60.0  0.62    9.75  2.7500  3.5630 No        
       2 US#5[M16]  60.0  0.62   11.25  3.5630  4.5098 No        
       2 US#4[M13]  60.0  0.40   10.50  3.1043  3.9793 Yes       
       2 US#4[M13]  60.0  0.40   12.00  3.9793  9.9793 Yes       
       2 US#5[M16]  60.0  0.62   12.00  4.5098  5.5098 Yes       
       2 US#5[M16]  60.0  0.62   12.00  5.5098 35.4902 Yes       
       2 US#5[M16]  60.0  0.62   12.00 35.4902 36.4902 Yes       
       2 US#4[M13]  60.0  0.40   12.00 31.0207 37.0207 Yes       
       2 US#4[M13]  60.0  0.40   10.50 37.0207 37.8957 Yes       
       2 US#5[M16]  60.0  0.62   11.25 36.4902 37.4370 No        
       2 US#5[M16]  60.0  0.62    9.75 37.4370 38.2500 No        
       2 US#5[M16]  60.0  0.62    9.00 38.2500 40.5000 No        
       2 US#4[M13]  60.0  0.40    9.00 37.8957 40.8957 Yes       
 
Top Steel:
 
  #bars    Size   Dist. from Top  Area  Start    End   Side Cover 
                       (in)      (in2)   (ft)    (ft)     (in)    
------------------------------------------------------------------
      1 US#4[M13]           2.00 0.200  0.0000  4.0000       3.00 
      1 US#4[M13]           2.00 0.200 37.0000 41.0000       3.00 
 
Bottom Steel:
 
  #bars Size Dist. from Top  Area Start  End Side Cover 
                  (in)      (in2)  (ft) (ft)    (in)    
--------------------------------------------------------
 
 
Span:1, Beam:3
 
PRESTRESSED STEEL:
 10 strands, 0.6''-LL-270-72.6, Low relaxation strands
Straight Pattern
 
END PATTERN (Ycg = 14.30 in):
 
  4 @  2.000 in 2 @  6.000 in 2 @ 10.000 in 2 @ 51.500 in 
 
REINFORCING STEEL:
 
  Tension steel:     
---------------------
  fy        60.0 ksi 
  Es       29000 ksi 
 
Stirrups:
 
  # legs    Size     fy   Area Spacing  Start    End    Extends  
                   (ksi) (in2)   (in)    (ft)    (ft)  into Deck 
-----------------------------------------------------------------
       2 US#4[M13]  60.0  0.40    9.00  0.1043  3.1043 Yes       
       2 US#5[M16]  60.0  0.62    9.00  0.5000  2.7500 No        
       2 US#5[M16]  60.0  0.62    9.75  2.7500  3.5630 No        
       2 US#5[M16]  60.0  0.62   11.25  3.5630  4.5098 No        
       2 US#4[M13]  60.0  0.40   10.50  3.1043  3.9793 Yes       
       2 US#4[M13]  60.0  0.40   12.00  3.9793  9.9793 Yes       
       2 US#5[M16]  60.0  0.62   12.00  4.5098  5.5098 Yes       
       2 US#5[M16]  60.0  0.62   12.00  5.5098 35.4902 Yes       
       2 US#5[M16]  60.0  0.62   12.00 35.4902 36.4902 Yes       
       2 US#4[M13]  60.0  0.40   12.00 31.0207 37.0207 Yes       
       2 US#4[M13]  60.0  0.40   10.50 37.0207 37.8957 Yes       
       2 US#5[M16]  60.0  0.62   11.25 36.4902 37.4370 No        
       2 US#5[M16]  60.0  0.62    9.75 37.4370 38.2500 No        
       2 US#5[M16]  60.0  0.62    9.00 38.2500 40.5000 No        
       2 US#4[M13]  60.0  0.40    9.00 37.8957 40.8957 Yes       
 
Top Steel:
 
  #bars    Size   Dist. from Top  Area  Start    End   Side Cover 
                       (in)      (in2)   (ft)    (ft)     (in)    
------------------------------------------------------------------
      1 US#4[M13]           2.00 0.200  0.0000  4.0000       3.00 
      1 US#4[M13]           2.00 0.200 37.0000 41.0000       3.00 
 
Bottom Steel:
 
  #bars Size Dist. from Top  Area Start  End Side Cover 
                  (in)      (in2)  (ft) (ft)    (in)    
--------------------------------------------------------
 
 
Span:1, Beam:4
 
PRESTRESSED STEEL:
 10 strands, 0.6''-LL-270-72.6, Low relaxation strands
Straight Pattern
 
END PATTERN (Ycg = 14.30 in):
 
  4 @  2.000 in 2 @  6.000 in 2 @ 10.000 in 2 @ 51.500 in 
 
REINFORCING STEEL:
 
  Tension steel:     
---------------------
  fy        60.0 ksi 
  Es       29000 ksi 
 
Stirrups:
 
  # legs    Size     fy   Area Spacing  Start    End    Extends  
                   (ksi) (in2)   (in)    (ft)    (ft)  into Deck 
-----------------------------------------------------------------
       2 US#4[M13]  60.0  0.40    9.00  0.1043  3.1043 Yes       
       2 US#5[M16]  60.0  0.62    9.00  0.5000  2.7500 No        
       2 US#5[M16]  60.0  0.62    9.75  2.7500  3.5630 No        
       2 US#5[M16]  60.0  0.62   11.25  3.5630  4.5098 No        
       2 US#4[M13]  60.0  0.40   10.50  3.1043  3.9793 Yes       
       2 US#4[M13]  60.0  0.40   12.00  3.9793  9.9793 Yes       
       2 US#5[M16]  60.0  0.62   12.00  4.5098  5.5098 Yes       
       2 US#5[M16]  60.0  0.62   12.00  5.5098 35.4902 Yes       
       2 US#5[M16]  60.0  0.62   12.00 35.4902 36.4902 Yes       
       2 US#4[M13]  60.0  0.40   12.00 31.0207 37.0207 Yes       
       2 US#4[M13]  60.0  0.40   10.50 37.0207 37.8957 Yes       
       2 US#5[M16]  60.0  0.62   11.25 36.4902 37.4370 No        
       2 US#5[M16]  60.0  0.62    9.75 37.4370 38.2500 No        
       2 US#5[M16]  60.0  0.62    9.00 38.2500 40.5000 No        
       2 US#4[M13]  60.0  0.40    9.00 37.8957 40.8957 Yes       
 
Top Steel:
 
  #bars    Size   Dist. from Top  Area  Start    End   Side Cover 
                       (in)      (in2)   (ft)    (ft)     (in)    
------------------------------------------------------------------
      1 US#4[M13]           2.00 0.200  0.0000  4.0000       3.00 
      1 US#4[M13]           2.00 0.200 37.0000 41.0000       3.00 
 
Bottom Steel:
 
  #bars Size Dist. from Top  Area Start  End Side Cover 
                  (in)      (in2)  (ft) (ft)    (in)    
--------------------------------------------------------
 
 
Span:1, Beam:5
 
PRESTRESSED STEEL:
 10 strands, 0.6''-LL-270-72.6, Low relaxation strands
Straight Pattern
 
END PATTERN (Ycg = 14.30 in):
 
  4 @  2.000 in 2 @  6.000 in 2 @ 10.000 in 2 @ 51.500 in 
 
REINFORCING STEEL:
 
  Tension steel:     
---------------------
  fy        60.0 ksi 
  Es       29000 ksi 
 
Stirrups:
 
  # legs    Size     fy   Area Spacing  Start    End    Extends  
                   (ksi) (in2)   (in)    (ft)    (ft)  into Deck 
-----------------------------------------------------------------
       2 US#4[M13]  60.0  0.40    9.00  0.1043  3.1043 Yes       
       2 US#5[M16]  60.0  0.62    9.00  0.5000  2.7500 No        
       2 US#5[M16]  60.0  0.62    9.75  2.7500  3.5630 No        
       2 US#5[M16]  60.0  0.62   11.25  3.5630  4.5098 No        
       2 US#4[M13]  60.0  0.40   10.50  3.1043  3.9793 Yes       
       2 US#4[M13]  60.0  0.40   12.00  3.9793  9.9793 Yes       
       2 US#5[M16]  60.0  0.62   12.00  4.5098  5.5098 Yes       
       2 US#5[M16]  60.0  0.62   12.00  5.5098 35.4902 Yes       
       2 US#5[M16]  60.0  0.62   12.00 35.4902 36.4902 Yes       
       2 US#4[M13]  60.0  0.40   12.00 31.0207 37.0207 Yes       
       2 US#4[M13]  60.0  0.40   10.50 37.0207 37.8957 Yes       
       2 US#5[M16]  60.0  0.62   11.25 36.4902 37.4370 No        
       2 US#5[M16]  60.0  0.62    9.75 37.4370 38.2500 No        
       2 US#5[M16]  60.0  0.62    9.00 38.2500 40.5000 No        
       2 US#4[M13]  60.0  0.40    9.00 37.8957 40.8957 Yes       
 
Top Steel:
 
  #bars    Size   Dist. from Top  Area  Start    End   Side Cover 
                       (in)      (in2)   (ft)    (ft)     (in)    
------------------------------------------------------------------
      1 US#4[M13]           2.00 0.200  0.0000  4.0000       3.00 
      1 US#4[M13]           2.00 0.200 37.0000 41.0000       3.00 
 
Bottom Steel:
 
  #bars Size Dist. from Top  Area Start  End Side Cover 
                  (in)      (in2)  (ft) (ft)    (in)    
--------------------------------------------------------
 

Span: 1, Beam: 1
 
PRECAST DATA:                                    GENERAL BRIDGE DATA:
-------------                                    --------------------
Section Id: IA-Std-D                            Bridge Width       =  36.33 ft
Type      : I-Girder                            Curb-to-curb       =  36.33 ft
Flng width: Top = 20.000 in    Bot = 22.000 in  Beam Spac. Lt./Rt. =   3.17/  7.50 ft
     thick: Top =  6.000 in    Bot =  8.000 in  Lane width         =  12.00 ft
Stems     : No  =  1                            Number of lanes    =   3
            Top =  7.000 in                     Interior/Exterior  =   Exterior
            Bot =  7.000 in                     Start Skew Angle   =   0.00 degrees
                                                End Skew Angle     =   0.00 degrees
Shear width     =  7.000 in                     
Minimum Thickness Criteria, Article 5.12.3.2 checked: OK.
 
TOPPING DATA:
-------------
Effective Deck Thickness   =   0.000 in
Sacrificial Deck Thickness   =   0.000 in
Haunch:
       Thickness =   0.000 in
       Width     =   0.000 in
Effective width  =  83.004 in (Art. 4.6.2.6.1)
 
GENERAL LOAD DATA:
------------------
Dead loads on precast:
---------------------
UNITS: (Point:  kips, Location: ft, Line:   klf, Trapez:   klf)
  DC/DW    Type     Mag.1     Loc.1    Mag.2     Loc.2
     DC  Line       0.068      0.00       0.068   40.00
     DC  Line       0.075      0.00       0.075   40.00
     DC  Trapez     0.056      0.00       0.056   20.00
     DC  Trapez     0.021      0.00       0.021   20.00
     DC  Trapez     0.726      0.00       0.726   20.00
     DW  Trapez     0.342     20.00       0.342   40.00
     DW  Line       0.117      0.00       0.117   40.00
     DW  Point      2.350     18.00      -         -   
     DW  Point      2.350     20.00      -         -   
     DW  Point      2.350     24.00      -         -   
     DW  Point      2.350     26.00      -         -   
 
Diaphragm loads: kips, ft
      Mag.      Loc.
      0.14    20.00 
 
Dead loads on composite: See Project info for composite loads
 
GENERAL SPAN DATA:
------------------
Overall length = 41.000 ft
Release length = 41.000 ft
Design  length = 40.000 ft
 
Kern points:
------------
Upper    =   38.18 in
Lower    =   13.01 in
 
DISTRIBUTION FACTORS (Art. 4.6.2.2):
------------------------------------
Type j, connected only enough to prevent relative vertical displacement
 
Live Moment (2+ lanes loaded)  : 0.907   (Calculated) (#)
Live Moment (1  lane  loaded)  : 0.907   (Calculated) (#)
Live Shear  (2+ lanes loaded)  : 0.907   (Calculated) (#)
Live Shear  (1  lane  loaded)  : 0.907   (Calculated) (#)
(#) Lever rule (C4.6.2.2.1)
The LL distribution computation is using the effective slab depth (ts = 0.00in).
Include sacrificial deck thick in ts:  NO
 
Dead Loads and Pedestrian Load distributed equally to all beams (Art. 4.6.2.2.1)
 
Pedestrian : 0.200   (Calculated)
 
Comp.  DC  : 0.200   (Calculated)
Comp.  DW  : 0.200   (Calculated)
 
RESISTANCE FACTORS (Art. 5.5.4.2):
----------------------------------
Flexure Reinforced:
   Compression controlled sections : 0.75
   Tension controlled sections     : 0.90
Flexure Prestressed:
   Compression controlled sections : 0.75
   Tension controlled sections     : 1.00
Shear                              : 0.90
 

Span: 1, Beam: 1
 
SECTION PROPERTIES:
-------------------
                             PRECAST          COMPOSITE
                             -------          ---------
Area                  =        638.7 in2            638.7 in2#
Total Height          =        54.00 in             54.00 in  
Mom. of Inertia (Ixx) =       214974 in4           214974 in4#
Ht. of c.g.           =        24.37 in             24.37 in#
Density               =       150.00 pcf           150.00 pcf
Lambda                =         1.00                 1.00 
Self-weight           =        665.3 plf            665.3 plf   
Mom. of Inertia (Iyy) =      14667.0 in4   
Poisson's Ratio       =          0.2
Thermal coeff.        =  0.000006000 1/F  
 
(#) Of Total Section using Ect/Ec = 0.9952

NOTE: Poisson's ratio may be assumed as 0.2 for lightweight concrete with specified compressive strengths
up to  10.0 ksi and for normal weight concrete with specified compressive strengths up to 15.0 ksi.

Use transformed strand and rebar: Strand Only
 
TRANSFORMED SECTION PROPERTIES:  
                 Bearing    Trans      H/2    0.10L    0.20L    0.30L    0.40L  Midspan
  Location,  ft     0.00     2.50     2.25     3.60     7.70    11.80    15.90    20.00
 
Precast: (At Release, using Ec =  4066.8 ksi )
  Area    , in2    640.9    651.7    650.7    651.7    651.7    651.7    651.7    651.7
  Yb      ,  in    24.34    24.17    24.19    24.17    24.17    24.17    24.17    24.17
  MI(Ixx) , in4   215194   216270   216164   216270   216270   216270   216270   216270
Composite: (At Final, using Ec =  4286.8 ksi )
  Area    , in2    640.7    651.0    649.9    651.0    651.0    651.0    651.0    651.0
  Yb      ,  in    24.34    24.18    24.20    24.18    24.18    24.18    24.18    24.18
  MI(Ixx) , in4   215180   216193   216094   216193   216193   216193   216193   216193

Span: 1, Beam: 1
 
STRESS LIMITS (Art. 5.9.2):
--------------------------
 
                            PRECAST               DECK
                            -------               ----
STRESS LIMITS AT RELEASE BEFORE LOSSES:
  Strength           =       4.50  ksi   
  Elasticity         =     4066.8 ksi   
  Max comp           =       2.93 ksi   
  Max tens           =      -0.19 ksi   
  Max tens,w/reinf   =      -0.51 ksi   
 
STRESS LIMITS AT FINAL AFTER LOSSES:
  Strength           =       5.00 ksi           4.00 ksi
  Elasticity         =    4286.83 ksi        4266.22 ksi
 
STRESS LIMITS AT FINAL 1 (P/S + DL + LL):
  Max comp           =       3.00 ksi           2.40 ksi
 
STRESS LIMITS AT FINAL 2 (P/S + DL):
  Max comp           =       2.25 ksi           1.80 ksi
 
FATIGUE I STRESS LIMITS AT FINAL 3 ( 50% P/S + 50% DL + F_LL ) (Art. 5.5.3.1):
  Max comp           =       2.00 ksi           1.60 ksi
 
SERVICE III (Tension):
  Max tens           =      -0.00 ksi          -0.38 ksi
 
 

Span: 1, Beam: 1
 
PRESTRESSED STEEL:  10 strands, 0.6''-LL-270-72.6, Low relaxation strands
Straight Pattern
END PATTERN (Ycg = 14.30 in):
     4 @  2.000 in     2 @  6.000 in     2 @ 10.000 in     2 @ 51.500 in
 
Strand Diameter       =    0.60 in       Tensile Strength(fpu) =      270.0 ksi
Strand Area           =    0.22 in2      Initial Prestress     =  0.73 fpu =   196.0 ksi
Total Strand Area     =    2.17 in2      Initial Pull          =      425.4 kips 
Trans. Len,bonded     =   3.000 ft       Dev. Len, bonded      =     10.837 ft
Trans. Len,debonded   =   3.000 ft       Dev. Len, debonded    =     13.546 ft
Holddown Force        =   0.000 kips     Beam Shrtng (PL/AE)   =      0.079 in
 
 
Span: 1, Beam: 1
 
ESTIMATED QUANTITIES
 
  Prestressing   Strands               Beam    Concrete      Stirrups      Longitudinal Bars 
   (linear ft) (LB/1000ft)   (LB)   Vol(C.Y.)   Wt(LB)         (LB)               (LB)       
---------------------------------------------------------------------------------------------
       410.000         740 303.400      6.735 27277.871  -40780283904.000       5.445        
 
 
REINFORCING STEEL: Tension steel: fy = 60.0 ksi Es =  29000 ksi
Stirrups:
    # legs     Size          fy         Area      Spacing       Start       End     Extends
                            (ksi)       (in2)       (in)         (ft)       (ft)    into Deck
   -------  ----------    --------    --------    --------     --------   --------- ----------
      2      US#4[M13]       60.00        0.40       9.00       0.1043      3.1043    Yes
      2      US#5[M16]       60.00        0.62       0.00       0.1250      0.1250     No
      2      US#5[M16]       60.00        0.62       9.00       0.5000      2.7500     No
      2      US#5[M16]       60.00        0.62       9.75       2.7500      3.5630     No
      2      US#4[M13]       60.00        0.40      10.50       3.1043      3.9793    Yes
      2      US#5[M16]       60.00        0.62      11.25       3.5630      4.5098     No
      2      US#5[M16]       60.00        0.62      12.00       4.5098      5.5098     No
      2      US#4[M13]       60.00        0.40      12.00       3.9793      9.9793    Yes
      2      US#4[M13]       60.00        0.40      18.00       9.9793     31.0207    Yes
      2      US#4[M13]       60.00        0.40      12.00      31.0207     37.0207    Yes
      2      US#5[M16]       60.00        0.62      12.00      35.4902     36.4902     No
      2      US#5[M16]       60.00        0.62      11.25      36.4902     37.4370     No
      2      US#4[M13]       60.00        0.40      10.50      37.0207     37.8957    Yes
      2      US#5[M16]       60.00        0.62       9.75      37.4370     38.2500     No
      2      US#5[M16]       60.00        0.62       9.00      38.2500     40.5000     No
      2      US#5[M16]       60.00        0.62       0.00      40.8750     40.8750     No
      2      US#4[M13]       60.00        0.40       9.00      37.8957     40.8957    Yes
 
Top Steel:
 
  #bars    Size   Dist. from Top  Area  Start    End   Side Cover 
                       (in)      (in2)   (ft)    (ft)     (in)    
------------------------------------------------------------------
      1 US#4[M13]           2.00 0.200  0.0000  4.0000       3.00 
      1 US#4[M13]           2.00 0.200 37.0000 41.0000       3.00 
 
 
Bottom Steel:
 
  #bars Size Dist. from Top  Area Start  End Side Cover 
                  (in)      (in2)  (ft) (ft)    (in)    
--------------------------------------------------------
 
---------------------------------------------------------------------------------------
Midspan: Str. area = 2.1700 in2       Ycg = 14.30 in
         P_init    =      425.4 kips  Ecc = 10.07 in
Days to release = 0.75  Rel. Humid.(RH) = 70.0 % Es = 28500.0 ksi  Eci =   4067 ksi
 
 
AASHTO LOSSES
Elastic Shortening     **     5.25 ksi  (Eq 5.9.5.2.3a-1), (fcgp= 0.749 ksi)
Elastic Gains                                                Gains       Adjustment
    due to Precast Loads                                   -0.90 ksi    0.00 ksi
    due to Composite Loads                                 -0.00 ksi    0.00 ksi
    due to Live Loads                                      -0.00 ksi    0.00 ksi
 
Time Dependent Losses (Approximate Method (Art.5.9.3.3))
                            Initial                            Final
 
Steel relaxation           0.00 ksi                         2.40 ksi (Eq 5.9.3.3-1)
Concrete shrinkage         0.00 ksi                        10.91 ksi (Eq 5.9.3.3-1)
Concrete creep             0.00 ksi                         6.05 ksi (Eq 5.9.3.3-1)
                       ------------                    ------------
Sub-total                  5.25 ksi  ( 2.68 %)            18.46 ksi ( 9.42 %)
Total Prestress Losses                                    23.71 ksi (12.09 %)
 
Prestressing Stress Limit Check (Table 5.9.3.1)
     initial fpi = 196.0 ksi < 0.75 fpu, OK 
     initial fpe = 172.3 ksi < 0.80 fpy, OK 
 
 
** Since the transformed section properties option has been selected, even though ES losses
have been calculated explicitly here, they are not included as a part of stress calculations.
Please see theory section for complete explanation.
 
---------------------------------------------------------------------------------------

 
SHEAR AND MOMENT ENVELOPE : Span : 1, Beam : 1, SERVICE I
Shears: kips, Moments: kft
 
                Bearing   Trans     H/2   0.10L   0.20L   0.30L   0.40L Midspan
Location,   ft     0.00    2.50    2.25    3.60    7.70   11.80   15.90   20.00
Self wt.  : M       0.0    31.2    28.3    43.6    82.7   110.7   127.5   133.1
(Max)       V      13.3    11.6    11.8    10.9     8.2     5.5     2.7     0.0
DL-Prec.  : M       0.0    34.3    31.1    47.5    86.7   110.0   117.4   108.9
DC(Max)     V      14.9    12.5    12.8    11.5     7.6     3.7     0.1     4.0
DL-Prec.  : M       0.0    20.3    18.3    29.0    60.3    89.5   116.8   137.4
DW(Max)     V       8.3     8.0     8.0     7.9     7.4     6.9     6.4     3.6
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       0.0     0.2     0.2     0.3     0.6     0.8     1.1     1.4
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+      0.0    86.0    77.9   120.4   230.3   311.1   362.8   380.8
            V      36.6    32.2    32.7    30.3    23.3    16.2     9.4     7.7
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx    36.6    32.2    32.7    30.3    23.3    16.2     9.4     7.7
            M       0.0    86.0    77.9   120.4   230.3   311.1   362.8   380.8
 
                  0.60L   0.70L   0.80L   0.90L     H/2   Trans Bearing
Location,   ft    24.10   28.20   32.30   36.40   37.75   37.50   40.00
Self wt.  : M     127.5   110.7    82.7    43.6    28.3    31.2     0.0
(Max)       V       2.7     5.5     8.2    10.9    11.8    11.6    13.3
DL-Prec.  : M      91.2    71.2    48.7    23.8    15.1    16.7     0.0
DC(Max)     V       4.6     5.2     5.8     6.4     6.6     6.5     6.9
DL-Prec.  : M     138.4   117.1    83.7    42.5    27.3    30.2     0.0
DW(Max)     V       3.0     7.2     9.1    11.0    11.6    11.5    12.6
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       1.1     0.8     0.6     0.3     0.2     0.2     0.0
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+    358.3   299.9   215.7   110.2    70.8    78.3     0.0
            V      10.4    17.9    23.1    28.3    30.0    29.7    32.9
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx    10.4    17.9    23.1    28.3    30.0    29.7    32.9
            M     358.3   299.9   215.7   110.2    70.8    78.3     0.0
 

 
REACTIONS (kips), SERVICE I
---------
 
Load Type          Left Support     Right Support
---------          ------------     -------------
Self Wt.               13.3             13.3
Deck+Haunch             0.0              0.0
Diaphragm               0.1              0.1
DL-Prec.(DC)           14.9              6.9
DL-Prec.(DW)            8.3             12.6
DL-Comp.(DC)            0.0              0.0
DL-Comp.(DW)            0.0              0.0
Live                    0.0              0.0
        Truck           0.0              0.0
        Lane            0.0              0.0
Pedestrian              0.0              0.0
 
Upward reactions are positive.
Live Load reactions are per lane with no distribution factor and no impact.
Reactions are not multiplied by Load Modifiers (ductility, redundancy and operational importance).
Non-composite load types are per beam.
Composite and Pedestrian load types are per total bridge width.

 
SHEAR AND MOMENT ENVELOPE : Span : 1, Beam : 1, SERVICE III
Shears: kips, Moments: kft
 
                Bearing   Trans     H/2   0.10L   0.20L   0.30L   0.40L Midspan
Location,   ft     0.00    2.50    2.25    3.60    7.70   11.80   15.90   20.00
Self wt.  : M       0.0    31.2    28.3    43.6    82.7   110.7   127.5   133.1
(Max)       V      13.3    11.6    11.8    10.9     8.2     5.5     2.7     0.0
DL-Prec.  : M       0.0    34.3    31.1    47.5    86.7   110.0   117.4   108.9
DC(Max)     V      14.9    12.5    12.8    11.5     7.6     3.7     0.1     4.0
DL-Prec.  : M       0.0    20.3    18.3    29.0    60.3    89.5   116.8   137.4
DW(Max)     V       8.3     8.0     8.0     7.9     7.4     6.9     6.4     3.6
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       0.0     0.2     0.2     0.3     0.6     0.8     1.1     1.4
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+      0.0    86.0    77.9   120.4   230.3   311.1   362.8   380.8
            V      36.6    32.2    32.7    30.3    23.3    16.2     9.4     7.7
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx    36.6    32.2    32.7    30.3    23.3    16.2     9.4     7.7
            M       0.0    86.0    77.9   120.4   230.3   311.1   362.8   380.8
 
                  0.60L   0.70L   0.80L   0.90L     H/2   Trans Bearing
Location,   ft    24.10   28.20   32.30   36.40   37.75   37.50   40.00
Self wt.  : M     127.5   110.7    82.7    43.6    28.3    31.2     0.0
(Max)       V       2.7     5.5     8.2    10.9    11.8    11.6    13.3
DL-Prec.  : M      91.2    71.2    48.7    23.8    15.1    16.7     0.0
DC(Max)     V       4.6     5.2     5.8     6.4     6.6     6.5     6.9
DL-Prec.  : M     138.4   117.1    83.7    42.5    27.3    30.2     0.0
DW(Max)     V       3.0     7.2     9.1    11.0    11.6    11.5    12.6
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       1.1     0.8     0.6     0.3     0.2     0.2     0.0
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+    358.3   299.9   215.7   110.2    70.8    78.3     0.0
            V      10.4    17.9    23.1    28.3    30.0    29.7    32.9
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx    10.4    17.9    23.1    28.3    30.0    29.7    32.9
            M     358.3   299.9   215.7   110.2    70.8    78.3     0.0
 


 
SHEAR AND MOMENT ENVELOPE : Span : 1, Beam : 1, STRENGTH I
Shears: kips, Moments: kft
 
                Bearing   Trans     H/2   0.10L   0.20L   0.30L   0.40L Midspan
Location,   ft     0.00    2.50    2.25    3.60    7.70   11.80   15.90   20.00
Self wt.  : M       0.0    39.0    35.3    54.5   103.4   138.4   159.3   166.3
(Max)       V      16.6    14.6    14.8    13.6    10.2     6.8     3.4     0.0
Self wt.  : M       0.0    28.1    25.4    39.2    74.5    99.6   114.7   119.8
(Min)       V      12.0    10.5    10.6     9.8     7.4     4.9     2.5     0.0
DL-Prec.  : M       0.0    42.9    38.9    59.4   108.4   137.5   146.8   136.1
DC(Max)     V      18.6    15.7    16.0    14.4     9.5     4.7     0.2     5.0
DL-Prec.  : M       0.0    30.9    28.0    42.8    78.1    99.0   105.7    98.0
DC(Min)     V      13.4    11.3    11.5    10.4     6.9     3.4     0.1     3.6
DL-Prec.  : M       0.0    30.5    27.5    43.5    90.4   134.3   175.2   206.2
DW(Max)     V      12.4    12.0    12.0    11.8    11.1    10.3     9.6     5.4
DL-Prec.  : M       0.0    13.2    11.9    18.9    39.2    58.2    75.9    89.3
DW(Min)     V       5.4     5.2     5.2     5.1     4.8     4.5     4.2     2.3
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Min)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       0.0     0.2     0.2     0.3     0.7     1.1     1.4     1.8
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1     0.1
Diaphragm : M       0.0     0.2     0.1     0.2     0.5     0.8     1.0     1.3
(Min)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Min)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Min)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+      0.0   112.6   101.9   157.8   302.9   411.2   482.7   510.4
            V      47.8    42.3    42.8    39.9    30.9    21.9    13.3    10.5
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx    47.8    42.3    42.8    39.9    30.9    21.9    13.3    10.5
            M       0.0    95.3    86.4   133.1   251.7   335.1   383.5   393.6
 
                  0.60L   0.70L   0.80L   0.90L     H/2   Trans Bearing
Location,   ft    24.10   28.20   32.30   36.40   37.75   37.50   40.00
Self wt.  : M     159.3   138.4   103.4    54.5    35.3    39.0     0.0
(Max)       V       3.4     6.8    10.2    13.6    14.8    14.6    16.6
Self wt.  : M     114.7    99.6    74.5    39.2    25.4    28.1     0.0
(Min)       V       2.5     4.9     7.4     9.8    10.6    10.5    12.0
DL-Prec.  : M     114.1    89.0    60.9    29.8    18.9    20.9     0.0
DC(Max)     V       5.8     6.5     7.2     8.0     8.2     8.1     8.6
DL-Prec.  : M      82.1    64.1    43.8    21.4    13.6    15.1     0.0
DC(Min)     V       4.1     4.7     5.2     5.7     5.9     5.9     6.2
DL-Prec.  : M     207.7   175.7   125.5    63.8    40.9    45.2     0.0
DW(Max)     V       4.5    10.8    13.7    16.5    17.4    17.2    19.0
DL-Prec.  : M      90.0    76.1    54.4    27.6    17.7    19.6     0.0
DW(Min)     V       1.9     4.7     5.9     7.1     7.5     7.5     8.2
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Min)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       1.4     1.1     0.7     0.3     0.2     0.2     0.0
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1
Diaphragm : M       1.0     0.8     0.5     0.2     0.1     0.2     0.0
(Min)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Min)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Min)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+    482.5   404.1   290.5   148.4    95.3   105.4     0.0
            V      13.7    24.2    31.2    38.2    40.4    40.0    44.3
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx    13.7    24.2    31.2    38.2    40.4    40.0    44.3
            M     364.8   304.5   219.4   112.2    72.1    79.7     0.0
 

 
REACTIONS (kips), STRENGTH I
---------
 
Load Type          Left Support     Right Support
---------          ------------     -------------
Self Wt.               16.6             16.6
Deck+Haunch             0.0              0.0
Diaphragm               0.1              0.1
DL-Prec.(DC)           18.6              8.6
DL-Prec.(DW)           12.4             19.0
DL-Comp.(DC)            0.0              0.0
DL-Comp.(DW)            0.0              0.0
Live                    0.0              0.0
        Truck           0.0              0.0
        Lane            0.0              0.0
Pedestrian              0.0              0.0
 
Upward reactions are positive.
Live Load reactions are per lane with no distribution factor and no impact.
Reactions are not multiplied by Load Modifiers (ductility, redundancy and operational importance).
Non-composite load types are per beam.
Composite and Pedestrian load types are per total bridge width.

 
Span : 1, Beam : 1, SERVICE I
 
RELEASE STRESSES, (ksi) (LOSS =  0.00 %)
 
               Trans   0.10L   0.20L   0.30L   0.40L Midspan Depress.
                      /0.90L  /0.80L  /0.70L  /0.60L
Location, ft    3.00    4.10    8.20   12.30   16.40   20.50   14.35
 
Beam-Self
Precast-top    0.063   0.083   0.148   0.194   0.222   0.231   0.211 
Bottom        -0.051  -0.067  -0.120  -0.157  -0.180  -0.187  -0.171 
 
Prestress
Precast-top    0.074   0.074   0.074   0.074   0.074   0.074   0.074 
Bottom         1.122   1.122   1.122   1.122   1.122   1.122   1.122 
 
Total
Precast-top    0.136   0.157   0.222   0.268   0.296   0.305   0.284 
Bottom         1.071   1.054   1.002   0.964   0.942   0.934   0.951 


 
 
SERVICE I
 
POSITIVE ENVELOPE STRESSES, (ksi) (LOSS =  9.88 %)
             Bearing   Trans     H/2   0.10L   0.20L   0.30L   0.40L Midspan
                                      /0.90L  /0.80L  /0.70L  /0.60L
 
Location, ft    0.00    2.50    2.25    3.60    7.70   11.80   15.90   20.00
 
Prestress
Precast-top    0.011   0.066   0.061   0.066   0.066   0.066   0.066   0.066
Bottom         0.172   1.011   0.929   1.011   1.011   1.011   1.011   1.011
 
Self wt.
Precast-top   -0.000   0.052   0.047   0.072   0.137   0.183   0.211   0.220
Bottom        -0.000  -0.042  -0.038  -0.058  -0.111  -0.148  -0.171  -0.178
 
DL-Prec (DC)
Precast-top   -0.000   0.057   0.052   0.079   0.144   0.182   0.194   0.180
Bottom        -0.000  -0.046  -0.042  -0.064  -0.116  -0.148  -0.157  -0.146
 
DL-Prec (DW)
Precast-top   -0.000   0.034   0.030   0.048   0.100   0.148   0.193   0.227
Bottom        -0.000  -0.027  -0.025  -0.039  -0.081  -0.120  -0.157  -0.184
 
Diaphragm
Precast-top   -0.000   0.000   0.000   0.000   0.001   0.001   0.002   0.002
Bottom        -0.000  -0.000  -0.000  -0.000  -0.001  -0.001  -0.002  -0.002
 
Deck + Haunch
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
DL-Comp (DC)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
DL-Comp (DW)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
LL+I(+)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
Final 1 (P/S + DL + LL)
Precast-top    0.011   0.209   0.190   0.266   0.448   0.581   0.667   0.697 
Bottom         0.172   0.896   0.824   0.849   0.702   0.594   0.524   0.500 
 
Final 2 (P/S + DL)
Precast-top    0.011   0.209   0.190   0.266   0.448   0.581   0.667   0.697 
Bottom         0.172   0.896   0.824   0.849   0.702   0.594   0.524   0.500 
 

 
Span : 1, Beam : 1, SERVICE III
 
RELEASE STRESSES, (ksi) (LOSS =  0.00 %)
 
               Trans   0.10L   0.20L   0.30L   0.40L Midspan Depress.
                      /0.90L  /0.80L  /0.70L  /0.60L
Location, ft    3.00    4.10    8.20   12.30   16.40   20.50   14.35
 
Beam-Self
Precast-top    0.063   0.083   0.148   0.194   0.222   0.231   0.211 
Bottom        -0.051  -0.067  -0.120  -0.157  -0.180  -0.187  -0.171 
 
Prestress
Precast-top    0.074   0.074   0.074   0.074   0.074   0.074   0.074 
Bottom         1.122   1.122   1.122   1.122   1.122   1.122   1.122 
 
Total
Precast-top    0.136   0.157   0.222   0.268   0.296   0.305   0.284 
Bottom         1.071   1.054   1.002   0.964   0.942   0.934   0.951 
 
As_top  , in2  0.000   0.000   0.000   0.000   0.000   0.000   0.000 
Ast_prvd, in2  0.200   0.000   0.000   0.000   0.000   0.000   0.000 


 
 
SERVICE III
 
POSITIVE ENVELOPE STRESSES, (ksi) (LOSS =  9.88 %)
             Bearing   Trans     H/2   0.10L   0.20L   0.30L   0.40L Midspan
                                      /0.90L  /0.80L  /0.70L  /0.60L
 
Location, ft    0.00    2.50    2.25    3.60    7.70   11.80   15.90   20.00
 
Prestress
Precast-top    0.011   0.066   0.061   0.066   0.066   0.066   0.066   0.066
Bottom         0.172   1.011   0.929   1.011   1.011   1.011   1.011   1.011
 
Self wt.
Precast-top   -0.000   0.052   0.047   0.072   0.137   0.183   0.211   0.220
Bottom        -0.000  -0.042  -0.038  -0.058  -0.111  -0.148  -0.171  -0.178
 
DL-Prec (DC)
Precast-top   -0.000   0.057   0.052   0.079   0.144   0.182   0.194   0.180
Bottom        -0.000  -0.046  -0.042  -0.064  -0.116  -0.148  -0.157  -0.146
 
DL-Prec (DW)
Precast-top   -0.000   0.034   0.030   0.048   0.100   0.148   0.193   0.227
Bottom        -0.000  -0.027  -0.025  -0.039  -0.081  -0.120  -0.157  -0.184
 
Diaphragm
Precast-top   -0.000   0.000   0.000   0.000   0.001   0.001   0.002   0.002
Bottom        -0.000  -0.000  -0.000  -0.000  -0.001  -0.001  -0.002  -0.002
 
Deck + Haunch
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
DL-Comp (DC)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
DL-Comp (DW)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
LL+I(+)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
Final 1 (P/S + DL + LL)
Precast-top    0.011   0.209   0.190   0.266   0.448   0.581   0.667   0.697 
Bottom         0.172   0.896   0.824   0.849   0.702   0.594   0.524   0.500 
 

 
VERTICAL SHEAR (Art. 5.8) - Span : 1, Beam : 1,  STRENGTH I
Using General Beta Theta Equation procedure - Art.5.7.3.4
Location (ft)
     Vu      bv    de     Aps      Vp    eps_x  Theta  Vs-reqd    Av/s    Av-prvd   Al_reqd
   (kips)   (in)  (in)   (in2)   (kips)                 (kips)  (in2/ft)  (in2/ft)   (in2)

    Mcor     a     dv      fpo   vu/fc   Vc-com  Beta  Max.spc.  min.Av/s  pVn/Vu       
    (kft)   (in)  (in)    (ksi)          (kips)          (in)    (in2/ft)             
*******************************************************************************************
Bearing :   0.50
     47.8    7.0   49.0    0.202   0.0   6.00e-3 50.0     32.1     0.157    1.360      0.00
      0.0    0.8   48.6     31.5 0.031      21.0 0.87    24.00     0.099    5.620 
Transfer:   3.00
     42.3    7.0   49.0    1.213   0.0  -0.10e-3 28.6      0.0     0.099    1.296      0.00
     95.3    4.6   46.7    189.0 0.029     120.2 5.20    24.00     0.099    8.693 
Critical:   4.38
     39.2    7.0   49.0    1.307   0.0  -0.12e-3 28.6      0.0     0.099    1.061      0.00
    143.7    5.0   46.5    189.0 0.027     121.4 5.27    24.00     0.099    9.342 
0.1L    :   4.10
     39.9    7.0   49.0    1.287   0.0  -0.12e-3 28.6      0.0     0.099    1.061      0.00
    133.1    4.9   46.6    189.0 0.027     121.1 5.26    24.00     0.099    9.192 
0.2L    :   8.20
     30.9    7.0   49.0    1.560   0.0  -0.14e-3 28.5      0.0     0.099    0.400      0.00
    251.7    5.9   46.1    189.0 0.021     122.3 5.36    24.00     0.099    8.499 
0.3L    :  12.30
     21.9    7.0   49.0    1.736   0.0  -0.15e-3 28.5      0.0     0.099    0.267      0.00
    335.1    7.3   45.4    189.0 0.015     121.7 5.42    24.00     0.099    9.572 
0.4L    :  16.40
     13.3    7.0   49.0    1.736   0.0  -0.15e-3 28.5      0.0     0.099    0.267      0.00
    383.5    7.3   45.4    189.0 0.009     121.4 5.41    24.00     0.099   15.764 
0.5L    :  20.50
     10.5    7.0   49.0    1.736   0.0  -0.15e-3 28.5      0.0     0.099    0.267      0.00
    393.6    7.3   45.4    189.0 0.007     121.4 5.41    24.00     0.099   19.976 
0.6L    :  24.60
     13.7    7.0   49.0    1.736   0.0  -0.15e-3 28.5      0.0     0.099    0.267      0.00
    364.8    7.3   45.4    189.0 0.010     121.7 5.42    24.00     0.099   15.284 
0.7L    :  28.70
     24.2    7.0   49.0    1.736   0.0  -0.16e-3 28.4      0.0     0.099    0.267      0.00
    304.5    7.3   45.4    189.0 0.017     122.1 5.44    24.00     0.099    8.684 
0.8L    :  32.80
     31.2    7.0   49.0    1.560   0.0  -0.15e-3 28.5      0.0     0.099    0.400      0.00
    219.4    5.9   46.1    189.0 0.021     122.9 5.39    24.00     0.099    8.443 
0.9L    :  36.90
     38.2    7.0   49.0    1.287   0.0  -0.12e-3 28.6      0.0     0.099    1.061      0.00
    112.2    4.9   46.6    189.0 0.026     121.4 5.27    24.00     0.099    9.609 
Critical:  36.62
     37.6    7.0   49.0    1.307   0.0  -0.12e-3 28.6      0.0     0.099    1.061      0.00
    121.3    5.0   46.5    189.0 0.026     121.6 5.28    24.00     0.099    9.734 
Transfer:  38.00
     40.0    7.0   49.0    1.213   0.0  -0.11e-3 28.6      0.0     0.099    1.296      0.00
     79.7    4.6   46.7    189.0 0.027     120.5 5.22    24.00     0.099    9.187 
Bearing :  40.50
     44.3    7.0   49.0    0.202   0.0   6.00e-3 50.0     28.2     0.138    1.360      0.00
      0.0    0.8   48.6     31.5 0.029      21.0 0.87    24.00     0.099    6.065 
 

ANCHORAGE ZONE REINFORCEMENT (Art. 5.9.4.4)
Span : 1, Beam : 1
Fpi,       kips =  425.36
fs,         ksi =   20.00
h/4,         in =   13.50
Abrst_rqrd, in2 =    0.85

CAMBER AND DEFLECTIONS: SERVICE I ( Span : 1, Beam : 1; Units: in )
 
               :     Release  Mult   Erection  Mult      Final
At 0.1 x L = 3.60 ft
Prestress      :       0.051  1.80      0.092  2.45      0.125
Self Wt.       :      -0.015  1.85     -0.028  2.70     -0.041
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.010  3.00     -0.031
Diaphragm      :                       -0.000  3.00     -0.000
DL-Prec. (DW)  :                       -0.011  3.00     -0.032
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.036            0.043            0.021
 
At 0.2 x L = 7.70 ft
Prestress      :       0.091  1.80      0.165  2.45      0.224
Self Wt.       :      -0.029  1.85     -0.053  2.70     -0.077
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.021  3.00     -0.063
Diaphragm      :                       -0.000  3.00     -0.001
DL-Prec. (DW)  :                       -0.022  3.00     -0.065
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.063            0.069            0.019
 
At 0.3 x L = 11.80 ft
Prestress      :       0.120  1.80      0.216  2.45      0.295
Self Wt.       :      -0.039  1.85     -0.072  2.70     -0.106
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.029  3.00     -0.086
Diaphragm      :                       -0.000  3.00     -0.001
DL-Prec. (DW)  :                       -0.031  3.00     -0.093
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.081            0.084            0.009
 
At 0.4 x L = 15.90 ft
Prestress      :       0.138  1.80      0.248  2.45      0.337
Self Wt.       :      -0.046  1.85     -0.085  2.70     -0.124
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.033  3.00     -0.099
Diaphragm      :                       -0.000  3.00     -0.001
DL-Prec. (DW)  :                       -0.037  3.00     -0.112
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.092            0.092            0.001
 
At 0.5 x L = 20.00 ft
Prestress      :       0.143  1.80      0.258  2.45      0.351
Self Wt.       :      -0.048  1.85     -0.089  2.70     -0.130
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.034  3.00     -0.101
Diaphragm      :                       -0.000  3.00     -0.001
DL-Prec. (DW)  :                       -0.040  3.00     -0.120
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.095            0.095           -0.001
 
At 0.6 x L = 24.10 ft
Prestress      :       0.138  1.80      0.248  2.45      0.337
Self Wt.       :      -0.046  1.85     -0.085  2.70     -0.124
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.031  3.00     -0.094
Diaphragm      :                       -0.000  3.00     -0.001
DL-Prec. (DW)  :                       -0.039  3.00     -0.116
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.092            0.093            0.003
 
At 0.7 x L = 28.20 ft
Prestress      :       0.120  1.80      0.216  2.45      0.295
Self Wt.       :      -0.039  1.85     -0.072  2.70     -0.106
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.026  3.00     -0.077
Diaphragm      :                       -0.000  3.00     -0.001
DL-Prec. (DW)  :                       -0.033  3.00     -0.099
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.081            0.085            0.012
 
At 0.8 x L = 32.30 ft
Prestress      :       0.091  1.80      0.165  2.45      0.224
Self Wt.       :      -0.029  1.85     -0.053  2.70     -0.077
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.018  3.00     -0.054
Diaphragm      :                       -0.000  3.00     -0.001
DL-Prec. (DW)  :                       -0.024  3.00     -0.071
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.063            0.070            0.021
 
At 0.9 x L = 36.40 ft
Prestress      :       0.051  1.80      0.092  2.45      0.125
Self Wt.       :      -0.015  1.85     -0.028  2.70     -0.041
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.009  3.00     -0.026
Diaphragm      :                       -0.000  3.00     -0.000
DL-Prec. (DW)  :                       -0.012  3.00     -0.035
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.036            0.043            0.023
 

ULTIMATE - Span : 1, Beam : 1,  STRENGTH I
(Mr-prvd computed by AASHTO equations, Art. 5.7.3.2/5.7.3.3)
 

Location (ft)
    Mu       dp    Aps    fps     c      a    Mr-prvd eps_t   Phi   Mcr    min Mr  Crkg  Mu-p/r
   k.ft      in    in2    ksi     in     in    k.ft                 k.ft    k.ft   Ratio Ratio
**********************************************************************************************
Transfer:   2.50
   112.6    39.7  1.517  259.0    5.8   4.62   1224.3  0.024T 1.00       -       -     -     -  
H/2     :   2.25
   101.9    39.7  1.390  259.9    5.3   4.25   1131.6  0.026T 1.00       -       -     -     -  
0.1L    :   3.60
   157.8    39.7  1.609  258.4    6.1   4.89   1290.5  0.023T 1.00       -       -     -     -  
0.2L    :   7.70
   302.9    39.7  1.950  256.1    7.3   5.88   1530.0  0.018T 1.00       -       -     -     -  
0.3L    :  11.80
   411.2    39.7  2.170  252.7    9.1   7.29   1665.6  0.014T 1.00   1468.5   546.9    1.13    -  
0.4L    :  15.90
   482.7    39.7  2.170  252.7    9.1   7.29   1665.6  0.014T 1.00   1468.5   642.0    1.13    -  
0.5L    :  20.00
   510.4    39.7  2.170  252.7    9.1   7.29   1665.6  0.014T 1.00   1468.5   678.8    1.13    -  
0.6L    :  24.10
   482.5    39.7  2.170  252.7    9.1   7.29   1665.6  0.014T 1.00   1468.5   641.7    1.13    -  
0.7L    :  28.20
   404.1    39.7  2.170  252.7    9.1   7.29   1665.6  0.014T 1.00   1468.5   537.5    1.13    -  
0.8L    :  32.30
   290.5    39.7  1.950  256.1    7.3   5.88   1530.0  0.018T 1.00       -       -     -     -  
0.9L    :  36.40
   148.4    39.7  1.609  258.4    6.1   4.89   1290.5  0.023T 1.00       -       -     -     -  
H/2     :  37.75
    95.3    39.7  1.390  259.9    5.3   4.25   1131.6  0.026T 1.00       -       -     -     -  
Transfer:  37.50
   105.4    39.7  1.517  259.0    5.8   4.62   1224.3  0.024T 1.00       -       -     -     -  

Legend: C = Compression-Controlled (0 < eps_t < 0.0020)
        I = In-Transition (0.0020 <= eps_t < 0.0050)
        T = Tension-Controlled (eps_t <= 0 or eps_t >= 0.0050)

Note  : fr used for calculating Mcr is computed using AASHTO method (Art.5.4.2.6.)

Consider Bottom Tension Steel Contribution : NO

 
 
DETENSIONING ( Span : 1, Beam : 1; Groups 1-5; Units: ksi )
 
Grp Str    Ys,in       3.00ft

  1   2 E   2.00 Ft    -0.067
        M   2.00 Fb     0.290
 
  2   2 E  51.50 Ft     0.384
        M  51.50 Fb     0.161
 
  3   2 E  10.00 Ft     0.349
        M  10.00 Fb     0.426
 
  4   2 E   6.00 Ft     0.266
        M   6.00 Fb     0.730
 
  5   2 E   2.00 Ft     0.136
        M   2.00 Fb     1.071
 
 

DESIGN SUMMARY
--------------
Span:  1,   Beam:  1,   Exterior beam
Beam type: I-Girder       , IA-Std-D       
Precast Length, ft: 41.00            Release Length, ft: 41.00
Strand Pattern: Straight              
Strand: 0.6''-LL-270-72.6       
Strand Es, ksi:    28500.0            No. of strands:  10
No. of strands, Draped:   0           No. of strands, Straight:  10
Concrete Strength, f'ci:   4.5  ksi        f'c:   5.0 ksi  f'ct   4.0 ksi
Initial losses:  2.68 %               Final losses: 12.09 %
 
Specification
-------------                            Allowable   Computed   Location    Status
Release Stresses (ksi) (Art. 5.9.2.3)
      Precast Bot (compression)             2.930       1.071     Trans       OK
      Precast Top w/ no reinf. (tension)   -0.190       0.136       Trans
      Precast Top w/ reinf. (tension)      -0.510           
Strength I (Art. 3.4.1, 5.6.3.1)       Provided     Required   Location   Status
      Ult. Moment (k.ft)                  1665.56      510.41     Midspan     OK
Debonding Limits (Art. 5.9.4.3.3)         Allowable    Computed              Status
      Max. Debond per Row                  40.00 %       0.00 %               OK
      Max. Debond Total                    25.00 %       0.00 %               OK
 
                       Final 1                     Final 2                     Final 3
Specification  Allow.  Comp.      Loc.     Allow.   Comp.      Loc.     Allow.   Comp.      Loc.
-------------  -----------------------     -------------------------     ------------------------
Positive Moment Envelope Stresses (ksi) (Art. 3.4.1 and 5.9.2.3.2)
  Service I Limit State - Compressive Stresses Only
    Pre.Top:   3.000   0.697     Midspan    2.250   0.697     Midspan
    Pre.Bot:   3.000   0.896    Transfer    2.250   0.896    Transfer
  Service III Limit State - Tensile Stresses Only
    Pre.Top:  -0.000   0.011     Bearing
    Pre.Bot:  -0.000   0.172     Bearing
 
CAMBER / DEFLECTION: (PCI Design Handbook - 7th Ed.- Table 5.8.2)
0.5 x L =  20.00 ft
               :     Release  Mult   Erection  Mult      Final
Prestress      :       0.143  1.80      0.258  2.45      0.351
Self Wt.       :      -0.048  1.85     -0.089  2.70     -0.130
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.034  3.00     -0.101
Diaphragm      :                       -0.000  3.00     -0.001
DL-Prec. (DW)  :                       -0.040  3.00     -0.120
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
 
Total          :       0.095            0.095           -0.001
 
Positive values indicate upward deflection.

LIVE LOADS - NONE
 
RATING LOADS - NONE

